40S逆龄精华（40S Anti-Aging Essence）

操作工艺Operation process：

1、将A相加入乳化锅加热搅拌温度至83±3℃，恒温半小时；

Add phase A to the emulsifying pot and heat and stir to 83±3℃, keep the temperature constant for half an hour;

2、继续搅拌并均质5分钟，均匀后边搅拌边'通冷却水；

Continue stirring and homogenizing for 5 minutes, and pass cooling water while stirring;

3、当料体温度降至55±5℃时，加入B相搅拌均匀，继续通冷却水：

When the material temperature drops to 55±5℃, add phase B and stir evenly, and continue to pass cooling water:

4、当料体温度降至45±5℃时，加入C相各料搅拌均匀：

When the material temperature drops to 45±5℃, add phase C and stir evenly:

5、继续加入D相各料搅拌均匀即可；

Continue to add phase D and stir evenly;

6、取样检验合格即可出料。

Samples can be discharged after passing the inspection.

********************************************************************************************************************************************

祛痘精华（Anti-acne essence）

操作工艺Operation process：

1、将A相加入乳化锅加热搅拌温度至83±3℃，恒温半小时；

Add phase A to the emulsifying pot and heat and stir to 83±3℃, keep the temperature constant for half an hour;

2、继续搅拌并均质5分钟，均匀后边搅拌边'通冷却水；

Continue stirring and homogenizing for 5 minutes, and pass cooling water while stirring;

3、当料体温度降至45±5℃时，加入B相搅拌均匀，继续通冷却水：

When the material temperature drops to 45±5℃, add phase B and stir evenly, and continue to pass cooling water:

4、继续加入C相搅拌均匀即可；

Continue to add phase C and stir evenly;

5、取样检验合格即可出料。

Samples can be discharged after passing the inspection.

********************************************************************************************************************************************

多肽保湿乳（Peptide Moisturizing Lotion）

操作工艺Operation process：

1、将A相加入水相锅加热搅拌温度至83±3℃，恒温半小时；

Add phase A to the water phase pot and heat and stir to 83±3℃, keep the temperature constant for half an hour;

2、将B相加入油相锅加热搅拌温度至83±3℃，恒温半小时；

Add phase B to the oil phase pot and heat and stir to 83±3℃, keep the temperature constant for half an hour;

3、将水相锅内原料抽入乳化锅，开启搅拌，然后再将油相锅内原料抽入乳化锅内,乳化锅的温度应保持在80-85℃；

Pump the raw materials in the water phase pot into the emulsification pot, start stirring, and then pump the raw materials in the oil phase pot into the emulsification pot. The temperature of the emulsification pot should be maintained at 80-85℃;

4、在乳化锅搅拌乳化10-15分钟, 然后均质8分钟，开始通冷却水；

Stir and emulsify in the emulsification pot for 10-15 minutes, then homogenize for 8 minutes, and start passing cooling water;

5、当料体温度降至55±5℃时，加入C相搅拌均匀，继续通冷却水；

When the material temperature drops to 55±5℃, add phase C and stir evenly, and continue to pass cooling water;

6、当料体温度降至45±5℃时，分别加入D相各料搅拌均匀；

When the material temperature drops to 45±5℃, add each material of phase D and stir evenly;

7、继续加入E相各料搅拌均匀即可。

Continue to add each material of phase E and stir evenly.

8、取样检验合格即可出料。

The material can be discharged after the sampling inspection is qualified.

********************************************************************************************************************************************

胶原补水面膜（Collagen Hydrating Mask）

 操作工艺Operation process：

1、将A相加入乳化锅加热搅拌温度至83±3℃，恒温半小时；

Add phase A to the emulsifying pot and heat and stir to 83±3℃, keep the temperature constant for half an hour;

2、边搅拌边均质5分钟，然后开始通冷却水；

Stir and homogenize for 5 minutes, then start to pass cooling water;

3、当料体温度降至55±5℃时，加入B相搅拌均匀，继续通冷却水；

When the temperature of the material drops to 55±5℃, add phase B and stir evenly, and continue to pass cooling water;

4、当料体温度降至45±5℃时，分别加入C相各料搅拌均匀；

When the temperature of the material drops to 45±5℃, add each material of phase C and stir evenly;

5、继续加入D相各料搅拌均匀即可。

Continue to add each material of phase D and stir evenly.

6、取样检验合格即可出料。

The material can be discharged after the sampling inspection is qualified.

********************************************************************************************************************************************

亮肤面膜（Brightening Mask）

 操作工艺Operation process：

1、将A相加入乳化锅加热搅拌温度至83±3℃，恒温半小时；

Add phase A to the emulsifying pot and heat and stir to 83±3℃, keep the temperature constant for half an hour;

2、边搅拌边均质5分钟，然后开始通冷却水；

Stir and homogenize for 5 minutes, then start to pass cooling water;

3、当料体温度降至55±5℃时，加入B相搅拌均匀，继续通冷却水；

When the temperature of the material drops to 55±5℃, add phase B and stir evenly, and continue to pass cooling water;

4、当料体温度降至45±5℃时，分别加入C相各料搅拌均匀；

When the temperature of the material drops to 45±5℃, add each material of phase C and stir evenly;

5、继续加入D相各料搅拌均匀即可。

Continue to add each material of phase D and stir evenly.

6、取样检验合格即可出料。

The material can be discharged after the sampling inspection is qualified.

********************************************************************************************************************************************

胶原补水面霜（Collagen Hydrating Cream）

操作工艺Operation process：

1、将A相加入水相锅加热搅拌温度至83±3℃，恒温半小时；

Add phase A to the water phase pot and heat and stir to 83±3℃, keep the temperature constant for half an hour;

2、将B相加入油相锅加热搅拌温度至83±3℃，恒温半小时；

Add phase B to the oil phase pot and heat and stir to 83±3℃, keep the temperature constant for half an hour;

3、将水相锅内原料抽入乳化锅，开启搅拌，然后再将油相锅内原料抽入乳化锅内,乳化锅的温度应保持在80-85℃；

Pump the raw materials in the water phase pot into the emulsification pot, start stirring, and then pump the raw materials in the oil phase pot into the emulsification pot. The temperature of the emulsification pot should be maintained at 80-85℃;

4、在乳化锅搅拌乳化10-15分钟, 然后均质8分钟，开始通冷却水；

Stir and emulsify in the emulsification pot for 10-15 minutes, then homogenize for 8 minutes, and start passing cooling water;

5、当料体温度降至55±5℃时，加入C相搅拌均匀，继续通冷却水；

When the material temperature drops to 55±5℃, add phase C and stir evenly, and continue to pass cooling water;

6、当料体温度降至45±5℃时，分别加入D相各料搅拌均匀；

When the material temperature drops to 45±5℃, add each material of phase D and stir evenly;

7、继续加入E相各料搅拌均匀即可。

Continue to add each material of phase E and stir evenly.

8、取样检验合格即可出料。

The material can be discharged after the sampling inspection is qualified.

********************************************************************************************************************************************

美白淡斑霜（Whitening and spot-lightening cream）

操作工艺Operation process：

1、将A相加入水相锅加热搅拌温度至83℃±3℃，恒温半小时；

Add phase A to the water phase pot and heat and stir to 83±3℃, keep the temperature constant for half an hour;

2、将B相加入油相锅加热搅拌温度至83±3℃，恒温半小时；

Add phase B to the oil phase pot and heat and stir to 83±3℃, keep the temperature constant for half an hour;

3、将水相锅内原料抽入乳化锅，开启搅拌，然后再将油相锅内原料抽入乳化锅内,乳化锅的温度应保持在80-85℃；

Pump the raw materials in the water phase pot into the emulsification pot, start stirring, and then pump the raw materials in the oil phase pot into the emulsification pot. The temperature of the emulsification pot should be maintained at 80-85℃;

4、在乳化锅搅拌乳化10-15分钟, 然后均质8分钟.

Stir and emulsify in the emulsification pot for 10-15 minutes, and then homogenize for 8 minutes.

5、均质完后边搅拌边通冷却水降温；

After homogenization, stir and cool with cooling water;

6、待体系温度降至55±5℃时，分别加入溶解好的C相和D相搅拌均匀，继续降温；

When the system temperature drops to 55±5℃, add the dissolved phase C and phase D respectively, stir evenly, and continue to cool;

7、待体系温度降至45±5℃时，分别加入E相各料搅拌均匀；

When the system temperature drops to 45±5℃, add the materials of phase E respectively and stir evenly;

8、继续加入F相各料搅拌均匀即可：

Continue to add the materials of phase F and stir evenly:

8、取样检验合格即可出料。

The material can be discharged after the sampling inspection is qualified.

备注：因为酵母菌多肽为发酵产物，容易变色，虽然体系作了缓冲，但长期接触光和空气仍容易令料体变色，因此建议用不透光且真空的容器装载。

Note: Because yeast polypeptide is a fermentation product, it is easy to change color. Although the system is buffered, long-term exposure to light and air can still easily cause the material to change color. Therefore, it is recommended to load it in a light-proof and vacuum container.